BluePrint Engines Pro Series GM LS 376ci 700hp T56 Manual Crate Engine w/ 3.0 Whipple, Natural Pulley Kit, Terminator X EFI System

The BluePrint Engines GM LS Compatible 376 ci is a masterclass in high-performance durability, engineered to deliver a staggering 700 horsepower and 640 lb-ft of torque with unwavering reliability. At the heart of this beast lies the Gen 6 / 3.0 Whipple Supercharger, providing instant, efficient boost and relentless power across the RPM range. The Holley Terminator X Max Gen IV ECU and harness system ensures precise engine management, while the advanced EFI system—complete with high-flow fuel injectors and rail—maintains optimal combustion under extreme conditions. Every supporting component, from the oil pan and coil packs to the spark plugs, wires, water pump, and harmonic balancer, is built to withstand the rigors of high-output operation. Paired with the T56 manual transmission, this setup offers smooth, torque-rich shifts that handle the power with ease. 

Description:

• Horsepower & Torque: 700 Horsepower / 640 ft. lbs. Torque
• Compression Ratio: 9.5:1
• BluePrint Engine LS3 Aluminum Heads
• BluePrint Engine Hydraulic Roller Cam
• BluePrint Engine Forged Pistons
• BluePrint Engine Forged Crankshaft

Block:

• BluePrint Engines High Strength Cast Iron Block
• Increased Deck Thickness and Strength Webbing
• Utilizes OEM LS3 Front and Rear Covers
• Improved Water Jacket Design
• Extended Cylinder Skirt
• 1-Piece Rear Main Seal
• Priority Main Oiling
• 4.070" Bore
• 6-Bolt Main

Rotating Assembly:

• Forged Crankshaft
• 3.622" Stroke
• 6.125"Connecting Rods w/ 150,000 PSI Bolts
• Forged Pistons - 10cc - Dish
• Internally Balanced Front and Rear

Cylinder Heads:

• BluePrint Aluminum Cylinder Heads - PS8015
• 70cc Chamber
• 2.165" Intake / 1.590" Exhaust Valves
• 259cc Intake / 102cc Exhaust Runners

Cam Specs:

• Hydraulic Roller Cam
• .612 Intake / .585 Exhaust Lift
• 225 Intake / 238 Exhaust Duration
• @.050-113 Degree Lobe Separation

Holley Terminator X Max Specific Features and Benefits:

• Real Time Fuel Map Learning Simplifies Tuning by Dynamically Adjusting the Base Fuel Rate
• On Board Bosch LSU 4.9 Wideband Control, Enabling Accurate AFR Readings and Closed Loop Tuning
• Eight High Impedance Injector Drivers, Ideal for Stock LS Injectors and Holley EFI Injectors
• Integrated 1-Bar MAP Sensor for Naturally Aspirated or Nitrous Setups, with Harness Support for External Higher Bar Sensors if needed
• 4 Configurable Inputs (12V, Ground, 5V, Frequency) and 2 Outputs (Ground, PWM) - Ideal for Electric Fans, Boost Control Solenoids, Nitrous Control and more
• Free PC Tuning Software via USB/CAN Interface for Full Laptop Control and Advance Setup
• Integrated 3.5" Touchscreen Handheld with Setup Wizard, Internal Data Logging, and Real Time Gauge Displays
• Terminator X Max ECU will Include a Base Timing Map Pre-Configured for this engine.

Also Includes: 

• Low Profile Rear Sump Oil Pan - BPP81073
• All Sensors Required for Engine to Run
• DBW Throttle Body - BPP12191019
• Gen 6 / 3.0 Whipple Supercharger
• Spark Plugs & Wires
• Harmonic Balancer
• Accelerator Pedal
• Timing Cover
• Valve Covers
• Coil Packs
• Oil Pump 
• Dipstick
• Natural Front Accessory Drive:
  • 150-amp Alternator
  • LT3 Style Water Pump
  • Power Steering Pump with Attached Reservoir
  • Compact Style Air Conditioning Compressor

Assembled with Complete T56 Six Speed Transmission Package:

• McLeod Super Steel Pro Dual Disk Clutch
• Bell Housing
• Billet Flywheel
• Engine Guard
• Starter
  • First Gear Ration: 2.66:1
  • Second Gear Ratio: 1.78:1
  • Third Gear Ration: 1.30:1
  • Fourth Gear Ration: 1.00:1
  • Fifth Gear Ration: 0.80:1
  • Sixth Gear Ration: 0.63:1

Notes:

• BPE recommends electric fans that produce 3000 cfm or more, for engines that are 400cid or less. Engines that are over 400cid BPE recommends 4000cfm or more.
• Please note, It is not necessary to run the Holley setup wizard, as this will erase the existing calibration loaded by BluePrint Engines. The ecu is fully unlocked and tunable for further adjustments once installed in customer vehicle.
• BluePrint Engines Recommends Air Intake Kit BPPLS01013 to ensure correct MAF calculations and Dyno calibration are maintained with the above ECU / tuning. 
• The front accessory drive on this engine fits many vehicles, however it is the customer responsibility to accurately measure and confirm fitment. Note this is a low-profile design, but things such as power steering hoses, alternator wiring, and additional fittings/fabrication may be required on some vehicles. 
• Engine/Trans Package Ships assembled

BluePrint engine the industry's best-in-class warranty for 30-months / 50,000 miles — with the extra confidence only BluePrint can provide. The warranty applies to individual or professional installations and is fully transferable.

Every BluePrint engine is Dyno tested and has strict parameters to pass and
be shipped to the customer. All parts are tested before being released for production:
• DC and Pneumatic assembly tools calibrated daily
• Fatigue Testing
• Durability Testing
• Random subassembly testing
• Quality system is ISO 9001: 2015 certified
• Traceable engine “DNA” electronic barcode record keeping of
manufacturing and performance data