null

QUICKTIME

Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193

PART NUMBER:
RM-193
MPN:
RM-193
Availability:
Ships from Manufacturer
Shipping:
Free over $98 in U.S. 48
Type:
Transmission Installation Kit
Bellhousing Included::
No
Crossmember Included::
No
Transmission Mount Included::
No
Transmission Tunnel Patch Included::
No
Yoke Included::
No
Pilot Bushing Included::
No
Speedometer Cable and Gear Included::
No
Backup Light Connector Harness Included::
No
Mounting Hardware Included::
Yes
Quantity::
Sold Individually
Notes::
If installing a T-56 to L83-L84 Gen V GM Engine, a kit is already provided for this swap in Lakewood Transmission Installation Kit #50375 that uses the proper plate and necessary hardware.
  • Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193
  • Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193
  • Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193
  • Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193
$153.95

Description

Quicktime GM LS T56 Magnum Transmission Space - 3/8" Aluminum RM-193

This .375-inch transmission spacer plate can be used on Tremec T-56, TR6060, & the T56 Magnum transmissions and is constructed of 6061 T-6 Aluminum. The RM-193 fits between the Bellhousing and Transmission to adjust where the input shaft falls for engines where the crank does not have enough depth or more clearance for certain clutch/flywheel setups or throwout/release bearings (ideal for some pressure plate styles or multi-plate clutch assemblies.)
*Longer transmission dowel pins and bolts are included. Spacer is made out of 6061-T6 Aluminum.
**If installing a T-56 to L83-L84 Gen V GM Engine, a kit is already provided for this swap in Lakewood Transmission Installation Kit #50375 that uses the proper plate and necessary hardware.
Information on choosing the proper pilot bearing for custom setups that may be useful on LS Swaps:
There are three different LS pilot bearings, each with a different outside diameter. The size you need will depend on the distance that your transmission input shaft protrudes past the front of the bellhousing.
Small pilot bearing (1.094 inches) - Typically used with GM LS1-powered vehicles from 1998 to 2002.
Medium pilot bearing (1.652 inches) - Typically used with GM LS3, LSA, LSX, and LS9-powered vehicles from 2003 to 2012. Oversize pilot bearing (1.705 inches) - Can be used with some aftermarket crankshafts and GM crate engines where the crankshaft pilot bearing bore is oversized.
Selecting the proper pilot bearing:
-Use a straight edge or yardstick to measure the distance that your transmission input shaft protrudes past the front of the bell housing.
-If the measurement is between 3/4 and 1 inch (19mm and 25.4mm), use the small diameter (1.094-inch) pilot bearing.
-If the measurement is between 1/4 and 3/8 inch (6.3mm and 9.5mm), test fit the medium outside diameter (1.652-inch)pilot bearing. The bearing should be a slight press fit into the crankshaft.
-If the medium diameter bearing is a loose fit, please use the large outside diameter (1.705-inch) bearing for a slight press fit into the crankshaft.
Installing the pilot bearing:
-Remove the old pilot bearing using a mechanical pilot bearing puller. Do not use a hydraulic method to remove the old bearing.
-Clean the crankshaft pilot bearing bore with a clean rag.
-Install the new pilot bearing into the crankshaft by driving or pressing on the outermost part of the bearing only. The bearing must be straight and fully seated into the crankshaft. Do not force the installation.
-Once the bearing is installed, spin the inner portion of the bearing to make sure it rotates freely and smoothly.
Important safety notes
-Do not move or disturb the press-in oil plug deep inside the crankshaft flange.
-Do not use a hydraulic method to push-out or remove the old pilot bearing.
-Be sure to install the new pilot bearing into the crankshaft by driving or pressing on the outermost part of the bearing only. The bearing must be straight and fully seated into the crankshaft. Do not force the installation.
View AllClose

Warranty Information

All Holley Performance Products Limited Warranties are extended to the original consumer only. This Limited Warranty is not assignable or otherwise transferable. There are no warranties that extend beyond those stated herein. Holley Performance Products offers no other warranties expressed or implied beyond this Limited Warranty. In the event of an alleged defect in material or workmanship, Holley Performance Products responsibility is strictly limited to repair or replace the defective product. Holley has no other obligation expressed or implied. Final warranty determination will be in the sole discretion of Holley Performance Products. Holley shall not be responsible for; (a) actual or alleged labor, transportation, or other incidental charges; or (b) actual or alleged consequential or other damages incurred by use of any product of Holley Performance Products. To initiate the warranty process, the consumer must return the alleged defective product to the place of purchase with a dated receipt and completed applicable warranty claim tag. Warranty claims will be rejected if the date of purchase cannot be established by the consumer. Do not send products directly to Holley Performance Products. Holley Performance Products assumes no responsibility for products sent directly to Holley Performance Products. This Limited Warranty sets forth specific legal rights. The consumer may have other rights as a result of variations in state laws or provincial laws. This Limited Warranty supersedes all prior warranty statements. HOLLEY/FLOWTECH/HOOKER/NOS/WEIAND NEW PRODUCT Holley Performance Products warrants its new Holley, Flowtech, Hooker, NOS, and Weiand products to be free from defects in material and workmanship for a period of 90 days from date of purchase. Holley Performance Products Limited Warranty specifically does not apply to products, which have been (a) modified or altered in any way; (b) subjected to adverse conditions, such as misuse, neglect, accident, improper installation or adjustment, dirt or other contaminants, water, corrosion, or faulty repair; or (c) used in other than those applications recommended by Holley Performance Products. Holley Performance Products also does not warrant, and disclaims all liability for products used in racing activities and/or applications other than those specifically recommended in the current brand catalog. Holley limits the warranty on Metallic Ceramic Coatings to be free from defects in material and workmanship for a period of 90 days from the date of purchase. This limited coating warranty does not apply to any products which have been subjected to adverse conditions, such as high heat encountered during engine break-in or if used during any racing activity.
View AllClose