null

HOLLEY

Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499

PART NUMBER:
558-499
UPC:
090127788370
MPN:
558-499
Shipping:
Free over $98 in U.S. 48
Type:
Transmission Controllers
Notes:
For use with Terminator X MAX ECU's, requires Terminator X V3 Build 100 or later firmware.
  • Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499
  • Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499
  • Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499
  • Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499
  • Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499
$511.95

Description

Holley Terminator X Max GM 6L80/90 Transmission Control Kit 558-499

For use with Terminator X MAX ECU's, requires Terminator X V3 Build 100 or later firmware.

Add GM 6L80/90E transmission control to any existing vehicle utilizing a Terminator X Max ECU. A departure from traditional Holley EFI transmission control, the Terminator X Max ECU allows the ability to use 2007+ GM 6L80E and 6L90E transmissions by communicating via CAN with the internal TCM (Transmission Control Module). The supplied Holley EFI OBDII Transmission Tuning Handheld is used to adjust Shift Points, Tire Size and Gear Ratio. The Terminator X V3 Software provides the ability to dial in Torque Management to optimize the desired shifting characteristics when using a 6L80/90E Transmission. Terminator X V3 software also allows a user to control the Secondary Shift Mode within the Transmission TCM and allows use of Tap Up/Down Shifting. Within Terminator X V3 PC Software o Virtual Torque Management Tables o Virtual TPS Tables to dial in shift characteristics regardless of engine o DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Handheld o Ability to read and clear TCM fault codes o Ability to raise and lower shift points by MPH or RPM Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode If you currently have a Terminator X ECU upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration

Within Terminator X V3 PC Software
o Virtual Torque Management Tables
o Virtual TPS Tables to dial in shift characteristics regardless of engine
o DBW and Timing torque reduction tables to create smooth shifts Within the Holley EFI OBDII Transmission Tuning Handheld
o Ability to read and clear TCM fault codes
o Ability to raise and lower shift points by MPH or RPM
Support for Tap Up/Tap Down & Transmission's Secondary Shift Mode
If you currently have a Terminator X ECU upgrading to a Terminator X Max ECU can be easily done by plugging your main harness into the Max ECU and re uploading your existing calibration

Features:

  • Included TCM handheld tuner with integrated wizard is required for setup in conjunction with the Terminator X 3.5” Handheld. Terminator X V3 software to unlocks optional tuning parameters.
  • Plug and play with any engine controlled by a Terminator X Max ECU
  • Supports - Shift Mode - Tap Up / Tap Down, and Torque Management
  1. Four loose wires:- Power (Red) – Supplies power to the transmission solenoids. This should be connected directly to the battery, or a constant battery source capable of supplying 5 amps
  2. Ground (Black) – Connect to a good chassis/engine ground source
  3. Brake Switch (Light Blue/White) – Wired to the brake light switch. This must be installed to a +12v source (as most brake light switches are)
  4. Park/Neutral Safety (Yellow) – Circuit for starter solenoid. When the transmission is in Park or Neutral this Yellow Wire will be Grounded (-). When the transmission is in gear this circuit will be open.

 

*Terminator X V3 Software is not compatible with Terminator X V1 or V2 ECU Firmware. To use V3 software with an older ECU version, the ECU and handheld MUST be updated to V3 Firmware. Opening a Terminator X V1 or V2 calibration with Terminator X V3 software, will update the calibration from V1 or V2 to V3. A V3 calibration cannot be loaded into a V1 or V2 ECU. A Terminator X V1 or V2 calibration cannot be used in a Terminator X ECU with V3 Firmware. The 3.5" TSLCD can be used to update the ECU & the Calibration from V1 or V2 to V3 when using Handheld Firmware V3 Build xx (tslcd35-terx.3.0.xx.fwu) or later.

 

View AllClose

Warranty Information

All Holley Performance Products Limited Warranties are extended to the original consumer only. This Limited Warranty is not assignable or otherwise transferable. There are no warranties that extend beyond those stated herein. Holley Performance Products offers no other warranties expressed or implied beyond this Limited Warranty. In the event of an alleged defect in material or workmanship, Holley Performance Products responsibility is strictly limited to repair or replace the defective product. Holley has no other obligation expressed or implied. Final warranty determination will be in the sole discretion of Holley Performance Products. Holley shall not be responsible for; (a) actual or alleged labor, transportation, or other incidental charges; or (b) actual or alleged consequential or other damages incurred by use of any product of Holley Performance Products. To initiate the warranty process, the consumer must return the alleged defective product to the place of purchase with a dated receipt and completed applicable warranty claim tag. Warranty claims will be rejected if the date of purchase cannot be established by the consumer. Do not send products directly to Holley Performance Products. Holley Performance Products assumes no responsibility for products sent directly to Holley Performance Products. This Limited Warranty sets forth specific legal rights. The consumer may have other rights as a result of variations in state laws or provincial laws. This Limited Warranty supersedes all prior warranty statements. HOLLEY/FLOWTECH/HOOKER/NOS/WEIAND NEW PRODUCT Holley Performance Products warrants its new Holley, Flowtech, Hooker, NOS, and Weiand products to be free from defects in material and workmanship for a period of 90 days from date of purchase. Holley Performance Products Limited Warranty specifically does not apply to products, which have been (a) modified or altered in any way; (b) subjected to adverse conditions, such as misuse, neglect, accident, improper installation or adjustment, dirt or other contaminants, water, corrosion, or faulty repair; or (c) used in other than those applications recommended by Holley Performance Products. Holley Performance Products also does not warrant, and disclaims all liability for products used in racing activities and/or applications other than those specifically recommended in the current brand catalog. Holley limits the warranty on Metallic Ceramic Coatings to be free from defects in material and workmanship for a period of 90 days from the date of purchase. This limited coating warranty does not apply to any products which have been subjected to adverse conditions, such as high heat encountered during engine break-in or if used during any racing activity.
View AllClose